Valley & City Plumbing KL
Get Estimate

Water Heater Repair & Installation in Kuala Lumpur & Selangor

Same-day hot water restored, done right the first time


When your shower runs cold at 6am, you need Water Heater Repair & Installation in Kuala Lumpur & Selangor that shows up fast and fixes it properly. We handle leaking tanks, tripping breakers, weak heating elements and full replacements for landed homes, condos and shophouses across the Klang Valley. Our licensed technicians carry parts for Joven, Rubine, Alpha and Panasonic units on every van, so most jobs finish in a single visit. Call us and we will tell you honestly whether your unit needs a repair or a replacement.

Technician installing or repairing a heating system in an indoor workshop setting.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed

What Our Water Heater Repair & Installation Covers

Every job includes a full diagnostic, the repair or installation itself, and a functional test before we leave. Here is what is covered in a standard visit, and what would be quoted separately if your situation needs it.

Full Diagnostic and Fault Report

We test the heating element with a multimeter, check the thermostat calibration, inspect the anode rod for corrosion, and pressure-test the inlet and outlet lines. You get a plain-language explanation of what failed and why, plus a written quote for the fix. Takes about 20 minutes.

Parts and Labour for Common Repairs

Heating element replacement, thermostat swap, pressure relief valve replacement, and connection resealing are all covered in a standard repair quote. We use Teflon tape and silicone sealant on every threaded joint. Parts are genuine or OEM-equivalent, and they carry a 90-day warranty.

New Unit Installation with Fittings

For replacements, the price includes removing and disposing of the old unit, installing the new heater, new flexible hoses, an isolation valve, and proper earthing to SPAN standards. We refill, bleed the air, and run the unit to full temperature before handover.

Leak Test and Safety Check

After any repair or install, we check every joint for leaks, confirm the pressure relief valve opens and reseats correctly, and verify the breaker and earth connection. We do not leave until the unit holds pressure and heats to the correct temperature. Usually 15 to 20 minutes.

Cleanup and Handover Walkthrough

We wipe down the work area, remove old parts and packaging, and walk you through the thermostat setting, the isolation valve position, and any maintenance you should know about. You get a written warranty card covering parts and our workmanship for 90 days.

What Water Heater Repair & Installation in Kuala Lumpur & Selangor Covers


Water Heater Repair & Installation in Kuala Lumpur & Selangor covers everything from a dripping pressure relief valve to a full tank swap on a 30-litre storage unit. We diagnose the fault first: checking the heating element with a multimeter, testing the thermostat, inspecting the magnesium anode rod for corrosion, and pressure-testing the inlet and outlet connections with a gauge. If the tank itself has rusted through, no repair will hold, and we will tell you straight. If it is a RM80 heating element, we replace it and you keep the same unit.

Most calls we get across Selangor come from three situations: a unit that suddenly stops heating, a puddle forming under the tank, or a homeowner upgrading to a tankless system for a renovated bathroom. In high-rise condos around Kelana Jaya and Sunway Mentari, low water pressure often trips the heater's safety cut-off, which looks like a total failure but is really a flow problem. In older landed homes in Kapar and Taman Melawati, hard water eats through heating elements in 18 to 24 months. We carry replacement elements, thermostats and Teflon tape on every van so we can fix it on the spot.

How Our Water Heater Repair Process Works

From the first phone call to hot water running again, here is exactly what happens when you book us.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

Pipe wrench and adjustable spanner set

Used to loosen and tighten inlet and outlet connections on storage and instant heaters. Essential for replacing flexible hoses and isolation valves without damaging the threads.

Digital multimeter

Tests heating elements for continuity and shorts to ground, and checks thermostat resistance. This is how we confirm whether an element is burnt out or the thermostat has drifted out of range.

Pressure gauge and leak detection kit

Measures incoming water pressure at the heater inlet and traces hidden leaks at joints. Low pressure is a common cause of tankless units failing to fire, and the gauge tells us immediately.

Pipe cutter and soldering torch

Cuts copper pipes cleanly and solders new joints when we reroute supply lines for a heater relocation or upgrade. Clean cuts and proper solder joints prevent future leaks.

Drain snake and hydro-jetter

Clears blockages in supply and drain lines that affect heater performance. A partially blocked inlet line drops pressure and trips the heater's safety cut-off, which looks like a heater fault.

Teflon tape, plumber's putty and silicone sealant

Seals every threaded connection and joint. We use Teflon tape on all metal threads, plumber's putty on drain fittings, and silicone sealant where a flexible seal is needed. No leaks when we leave.

Methods & Standards

SPAN-compliant earthing and wiring

Every water heater installation follows Suruhanjaya Perkhidmatan Air Negara requirements for electrical earthing and pressure relief. We run a dedicated earth wire, install a correctly rated breaker, and test earth continuity before powering the unit. This protects against shock and satisfies condo management inspections.

Pressure testing before handover

After any repair or installation, we refill the system and pressure-test every joint at operating pressure for at least 10 minutes. If a joint weeps, we reseal it before we call the job done. This is why our callback rate for leaks is very low.

Anode rod inspection and replacement

The magnesium anode rod sacrifices itself to protect the tank from corrosion. We inspect it on every service and replace it when it is more than 50 percent consumed. A fresh anode rod can double the life of a storage tank, especially in hard water areas.

Element descaling and tank flush

In hard water areas, scale builds on the heating element and insulates it, forcing it to work harder and eventually fail. We descale the element and flush the tank to remove sediment. This restores heating efficiency and extends element life by 12 to 18 months.

When to Call Us for Water Heater Service

01

Your storage heater is over 8 years old and starts making popping or rumbling sounds during heating.

What we do: Popping means sediment has built up on the heating element and the tank floor. We drain and flush the tank, inspect the anode rod, and replace the element if it is scaled. If the tank is sound, a flush and element swap adds years of life for a fraction of replacement cost.

→ Quieter operation, faster heating, and lower electricity bills. Most customers get another 3 to 5 years out of the unit before replacement is needed.

02

You are renovating a bathroom and want to switch from a bulky storage tank to a slim tankless instant heater.

What we do: We assess your incoming water pressure, route new copper or PEX pipes to the new heater position, install the tankless unit, and run dedicated wiring with proper earthing to SPAN standards. We coordinate with your contractor so the plumbing is ready before tiling starts.

→ A space-saving installation that heats water on demand, with no standby heat loss. Typical install takes 2 to 3 hours, and you get hot water the same day.

03

You just bought a subsale condo in Pusat Bandar Puchong and the existing water heater has no warranty or service history.

What we do: We do a full inspection: element test, thermostat check, anode rod condition, pressure relief valve function, and earth continuity. If the unit is sound, we service it and give you a baseline. If it is near end of life, we quote a replacement so you can budget for it.

→ You know exactly what you have and what it will cost to keep it running. No surprises three months after moving in.

04

Your water heater starts leaking on a Sunday night and you have guests arriving Monday morning.

What we do: Call our 24/7 emergency line. We isolate the supply, stop the leak, and either repair the unit or install a replacement from our van stock. For common Joven and Alpha models, we usually have the right unit available for same-night installation.

→ Hot water restored before your guests arrive, and no water damage spreading across the floor overnight.

How Water Heater Repair & Installation Runs in Selangor

Selangor's water supply is moderately hard, and that shapes almost every water heater job we do here. In areas like Kapar, Klang and parts of Shah Alam, the calcium content in the water coats heating elements with scale within 18 to 24 months, which is faster than most manufacturers expect. We see far more element failures than thermostat failures in these areas, and we recommend an annual flush to stretch element life. In high-rise condos around Kelana Jaya, Sunway Mentari and KLCC, the issue is usually pressure, not water quality. Gravity-fed supply from the building's rooftop tank can drop below the minimum flow rate a tankless heater needs to fire, so the unit appears dead when it is actually fine. We test incoming pressure first and often find a partially closed isolation valve or a clogged inlet filter. For landed homes in Bangi, Denai Alam and Kota Warisan, we deal with older wiring that may not have a proper earth connection, which is a safety issue we correct on every visit. If you need water heater installation in Selangor for a new home, we coordinate with your developer or contractor to get the pipe routing and wiring right before the walls are closed up.

Neighborhoods We Serve

  • Kelana Jaya

    Many condos here have gravity-fed hot water lines with variable pressure. Tankless heaters often fail to fire during peak morning hours, so we test flow rate before recommending a unit.

  • Kapar

    Hard water is a real problem in Kapar. We see heating elements scaled solid in under two years. Annual descaling and a fresh anode rod make a big difference to unit lifespan here.

  • Sri Hartamas

    Mix of older terrace houses and newer condos. Older homes often need a full rewire to support a modern heater, and we handle the earthing and breaker upgrade in the same visit.

  • Pusat Bandar Puchong

    High-density condo area with many Joven and Alpha storage units reaching end of life. We carry common replacement models on the van for same-day swap-outs.

  • Bangi

    Landed homes with multiple bathrooms, often running two or three separate heaters. We frequently install tankless units to replace ageing storage tanks and free up bathroom space.

Local Conditions We Plan For

  • Moderately hard water across most of Selangor

    Scale builds on heating elements faster than in soft-water regions, shortening element life to 18 to 24 months in hard-hit areas. Annual flushing and descaling is the single best way to extend unit life.

  • High-rise gravity-fed water supply in condo clusters

    Incoming pressure can drop below the minimum flow rate for tankless heaters, causing them to cut out. We test pressure at the inlet and recommend a pump upgrade if the building supply is consistently weak.

  • Older landed homes with outdated wiring

    Many pre-2000 homes in Selangor lack a proper earth connection at the heater point. We correct this on every installation to meet SPAN requirements and eliminate shock risk.

  • Year-round humid tropical climate

    High humidity accelerates corrosion on exposed metal fittings and tank exteriors. We use corrosion-resistant fittings and check the tank base for rust on every service call.

Burnt Element Replaced in Kelana Jaya Condo

Before

A 6-year-old Joven storage heater stopped producing hot water. The homeowner had been resetting the breaker daily for a week. The element had burnt out and was shorting to ground, which tripped the breaker every time the thermostat called for heat.

After

We replaced the heating element, tested the thermostat, and verified earth continuity. The breaker held under full load, and the unit reached 65 degrees Celsius in 25 minutes. Total cost was RM280, and the homeowner cancelled the new unit they had been about to buy.

Maintenance: We recommended an annual tank flush to remove sediment and prevent the new element from scaling. In Kelana Jaya's water conditions, that flush adds 12 to 18 months to element life.

Before

A family of five in Bangi had two ageing storage heaters, one of which was leaking from the tank base. The bathroom was cramped, and the old units took up significant wall space. Both were over 10 years old with no service history.

After

We removed both storage tanks and installed a single tankless instant heater with new copper pipe routing and dedicated wiring. The install took 2.5 hours. The bathroom gained about 0.5 square metres of usable space, and hot water is now unlimited.

Maintenance: Tankless units need an annual descaling of the heat exchanger, especially in Selangor's hard water. We showed the homeowner how to flush the unit and booked a reminder for 12 months out.

Before

A landlord in Kapar had three rental units where the water heaters kept cutting out. Two plumbers had already replaced elements and thermostats with no lasting fix. The real issue was low incoming water pressure causing the safety cut-off to trip.

After

We installed a Grundfos pressure pump to stabilise flow to all three units. The heaters stopped tripping immediately. Over the next eight months, the landlord had zero heater callbacks, saving an estimated RM1,200 in repeat repair costs.

Maintenance: We check the pump pressure setting and clean the inlet strainer every 12 months. A stable supply pressure is what keeps the heaters running without nuisance cut-offs.

Water Heater Problems We Fix Across Selangor

Most water heater calls fall into a handful of patterns. Here are the ones we see most often, what happens if you ignore them, and how we sort them out.

Problem

Water heater not heating at all

No hot water for showers, washing, or cleaning. If the element has failed and you keep resetting the breaker, you risk damaging the thermostat and control board, turning a RM250 repair into a RM700 replacement.

Our Fix

We test the element and thermostat with a multimeter, identify which part failed, and replace it on the spot. Most no-heat calls are a burnt element or a tripped safety cut-off from low pressure. We fix the part and check the flow so it does not recur.

Problem

Water leaking from the tank or connections

A slow drip under the heater warps flooring, stains walls, and can short the electrical connections. If the tank body itself is leaking, it will not stop on its own and the unit needs replacing before it floods the room.

Our Fix

We isolate the supply, identify whether the leak is at a fitting or the tank itself, and repair or replace accordingly. Fitting leaks get resealed with Teflon tape and plumber's putty. Tank leaks mean a new unit, and we install it the same day.

Problem

Breaker keeps tripping when heater runs

You cannot use the heater without cutting power to half the house. Repeated tripping stresses the wiring and the breaker itself, and in the worst case creates a fire risk from an overloaded circuit.

Our Fix

We check the earth connection, test the element for a short to ground, and inspect the wiring for corrosion or loose terminals. Often it is a failed element leaking current to earth. We replace the element, verify the earth, and confirm the breaker holds under full load.

Problem

Low water pressure at the hot tap only

The heater may run but the flow is weak, and in tankless units low pressure stops the heater from firing at all. Sediment and scale in the inlet filter or a partially closed isolation valve are the usual culprits.

Our Fix

We clean or replace the inlet filter, flush the line, and check the isolation valve position. If the whole house has weak pressure, we test the supply and recommend a Grundfos or Wilo pump upgrade. Most hot-tap-only pressure issues are fixed in under an hour.

Why Homeowners Call Us for Water Heater Service

Why Homeowners Call Us for Water Heater Service

A cold shower is not a small inconvenience when you have a family getting ready for work and school. Here is what you get when you book our team.

  • Same-Day Hot Water

    We keep Joven, Alpha, Rubine and Panasonic heating elements, thermostats and pressure valves stocked on every van. That means 8 out of 10 repair jobs are finished in a single visit, usually within 2 to 3 hours of arrival. You are not waiting three days for a part order while the family showers cold.

  • Licensed and Code-Correct

    Every installation follows Suruhanjaya Perkhidmatan Air Negara (SPAN) requirements for water heater wiring and pressure relief. We earth the unit properly, install an isolation valve, and test the relief valve before we leave. A wrongly earthed heater is a shock risk, and we have seen too many DIY jobs in Bangi and Denai Alam with no earth wire at all.

  • Upfront Pricing, No Surprises

    You get the price before we start. A standard element replacement runs RM180 to RM350 including parts and labour. A full storage tank swap is RM450 to RM900 depending on capacity and brand. We quote the job, you approve it, and the bill matches the quote. No hidden call-out charges tacked on at the end.

  • Warranty on Parts and Labour

    Every repair we do carries a 90-day workmanship warranty, and new units carry the full manufacturer warranty on top. If the same fault comes back within 90 days, we return and fix it at no charge. That covers the heating element, thermostat, pressure valve and all wiring connections we touched.

Credentials and Customer Proof

Licensed & Certified

  • Certified Plumber (Malaysia) — issued by Certified Plumber Malaysia
  • SPAN Licensed Plumbing Contractor — issued by Suruhanjaya Perkhidmatan Air Negara
  • CIDB Registered Contractor — issued by Construction Industry Development Board Malaysia
  • MS ISO 9001 Quality Management — issued by Department of Standards Malaysia

Verified Reviews

Google ★★★★★4.9

Called at 8am about a leaking heater, technician arrived by 9:30. He showed me the cracked fitting, quoted RM220, and had it fixed in 40 minutes. No mess, no upselling. The price was exactly what he said on the phone. Will use again for my other unit.

Google ★★★★★4.8

We had three plumbers fail to fix our tripping heater in Kapar. Valley & City diagnosed it as a pressure problem in 15 minutes and installed a pump. Eight months later, zero issues. They actually understand the root cause instead of just swapping parts.

Google ★★★★★5.0

Installed a tankless heater during our bathroom renovation in Sri Hartamas. They coordinated with our contractor, handled the wiring and earthing, and passed the condo management inspection without any issues. Clean work and finished on schedule.

Google ★★★★★4.9

Booked a same-day replacement for an old Joven unit in Pusat Bandar Puchong. They had the model on the van, removed the old one, installed the new one, and tested everything in under two hours. Fair price and proper warranty card given.

Local Experience You Can Rely On

Our technicians hold Certified Plumber (Malaysia) credentials and work under a SPAN-licensed plumbing contractor. We have repaired and installed thousands of water heaters across the Klang Valley, from single-unit condos in KLCC to terrace houses in Bangi with three bathrooms running off separate heaters. Every technician trains on current Joven, Alpha, Rubine, Panasonic and Daikin models, including tankless and heat pump systems. We also hold CIDB registration, which matters when your condo management or local council asks for contractor credentials before approving work.

  • Certified Plumber (Malaysia) with SPAN-licensed contractor backing on every job
  • Trained on Joven, Alpha, Rubine, Panasonic and Daikin heater models
  • CIDB-registered for condo and commercial building access approval
  • Carry pipe wrenches, multimeters, pressure gauges and leak detection kits on every van
  • Experienced with both storage tank and tankless instant heating systems
Get Started Today
Local Experience You Can Rely On

Cities We Serve for Water Heater Repair & Installation

Our team delivers Selangor water heater service across the Klang Valley, from the KL city core out to the newer townships in the south and west. Each area has its own building types and water conditions, and we adjust our approach accordingly. Whether you are in a high-rise condo or a landed terrace, we bring the right parts and the right method for your property.

KLCC

High-rise condos and serviced apartments with centralised water systems. We handle tankless and storage heater repairs with strict building management access procedures and SPAN-compliant earthing.

Sri Hartamas

A mix of older terrace houses and modern condos. Many homes here need wiring upgrades before a new heater install, and we handle the earthing and breaker work in the same visit.

Segambut

Industrial and residential mix with many older shophouses and terrace homes. We repair storage heaters and replace corroded fittings in buildings where the plumbing has not been updated in years.

Denai Alam

Newer township with modern terrace homes and semi-detached houses. Most jobs here are tankless installations and warranty-period repairs on builder-installed units that have developed faults.

Kelana Jaya

Dense condo cluster with gravity-fed water supply. Low pressure often trips tankless heaters, so we test flow rate first and recommend a pump upgrade when the building supply is weak.

Sunway Mentari

Commercial and residential area with a mix of shop offices and apartments. We service heaters in both, often working around business hours to avoid disrupting shop operations.

Kapar

Hard water area where heating elements scale up fast. We recommend annual descaling and carry replacement elements on the van for same-day repair on common Joven and Alpha models.

Pusat Bandar Puchong

High-density condo area with many ageing storage units. We stock common replacement models for same-day swap-outs and handle the disposal of old units.

Taman Melawati

Hillside residential area with older landed homes. Many properties here have outdated wiring, so we check earth continuity and upgrade the breaker when installing a new heater.

Bangi

Landed homes with multiple bathrooms, often running two or three heaters. We frequently install tankless units to replace ageing tanks and free up wall space in smaller bathrooms.

Kota Warisan

Fast-growing township near the airport with new terrace and semi-D homes. Most calls are new installations and warranty repairs, and we coordinate with developers on pipe routing.

What Our Customers Say

Real experiences from customers who chose our Water Heater Repair & Installation services.

“Our Joven heater stopped heating on a Friday night. I called at 9pm and the technician arrived by 10:30. He tested the element, found it burnt out, and had a replacement on the van. By 11:15 we had hot water again. Cost RM280, exactly what he quoted on the phone. No drama, no upselling.”

F

Farah A.

Homeowner, Kelana Jaya

“I manage four rental units in Kapar and the water pressure is terrible, so heaters keep tripping. Valley & City came out, diagnosed it as a flow problem not a heater problem, and installed a Grundfos pump. All four units have been running fine for eight months now. They fixed the cause.”

R

Ramesh K.

Landlord, Kapar

“I wanted to switch from a storage tank to a tankless unit during my bathroom renovation. They handled the new wiring, the pipe routing, and the SPAN-compliant earthing. Took about 2.5 hours. The condo management approved their CIDB registration without any issues. Clean work, no mess left behind.”

M

Mei Ling T.

Condo Owner, Sri Hartamas

Pasang Water Heater di Kuala Lumpur & Selangor

Perlukan khidmat pemasangan water heater untuk rumah atau pejabat? Valley & City Plumbing KL menyediakan pasang water heater, baiki dan tukar water heater di Kuala Lumpur dan Selangor, 24 jam sehari, 7 hari seminggu.

Cara pasang water heater

01

Semakan

Kami semak lokasi pemasangan, bekalan elektrik dan paip air sebelum kerja bermula.

02

Pemasangan

Unit water heater dipasang dengan selamat pada dinding atau lokasi yang sesuai.

03

Sambungan paip

Paip air masuk dan keluar disambung, termasuk injap keselamatan.

04

Ujian

Kami uji tekanan, periksa kebocoran dan suhu air sebelum serahan.

Hubungi +60178717384 untuk sebut harga pemasangan water heater di kawasan anda.

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How much does water heater repair cost in Kuala Lumpur and Selangor?
Most repairs run RM180 to RM450 in 2026, depending on the part. A heating element replacement is RM180 to RM350. A thermostat swap is RM150 to RM280. A pressure relief valve is RM120 to RM200. If the tank itself is cracked or rusted through, repair is not viable and a new unit costs RM450 to RM1,200 installed. We quote before we start, so you know the number upfront.
Who installs water heaters in KL and Selangor?
We do. Our technicians are Certified Plumber (Malaysia) and work under a SPAN-licensed contractor. We install storage tank, instant and tankless units for landed homes, condos and shophouses across the Klang Valley. Installation includes new flexible hoses, an isolation valve, proper earthing and a pressure test before we hand over. Call +60178717384 to book.
Why is my water heater not heating in Malaysia?
The three most common causes are a burnt-out heating element, a faulty thermostat, or a tripped safety cut-off from low water pressure. In hard water areas like Kapar and parts of Klang, scale builds on the element and shortens its life to 18 to 24 months. A multimeter test takes 10 minutes and tells us exactly which part failed. We carry replacements on the van.
How long does water heater installation take in Kuala Lumpur?
A standard storage tank replacement takes 1.5 to 2 hours. A tankless or instant heater install runs 2 to 3 hours because it involves new wiring and pipe routing. If we are replacing an old unit with the same model, it is faster, usually under 90 minutes. We test the unit to full temperature before we leave, so you know it works.

Related Services

Emergency Plumbing Service

A burst pipe or sudden water heater leak at midnight needs the same fast response. Our emergency team handles both, so if your heater is spraying water across the bathroom floor, one call covers it. We isolate the supply, stop the leak, and repair or replace the unit.

View Emergency Plumbing Service

Clogged Drain Clearing

Low water pressure from a clogged line can trip your heater's safety cut-off and make it look like the unit failed. We clear the blockage with a drain snake or hydro-jetter, restore proper flow, and confirm your heater runs normally again before we leave.

View Clogged Drain Clearing

Pipe Leak Repair

A leaking pipe near your water heater inlet wastes water and drops pressure to the unit. We trace the leak with a detection kit, repair or replace the section using copper or PEX pipes, and pressure-test the line so your heater gets steady flow again.

View Pipe Leak Repair

Toilet Repair & Installation

When we are already at your home for a water heater job, many customers ask us to look at a running toilet or leaking faucet. We handle both on the same visit, saving you a second call-out fee. Parts are usually on the van.

View Toilet Repair & Installation

Water Pump Installation

If your water heater keeps cutting out because of weak pressure, the real fix might be a pump upgrade. We install Grundfos and Wilo pressure pumps that stabilise flow to your heater and every tap in the house. We size the pump to your home's demand.

View Water Pump Installation

Bathroom Renovation Plumbing

Renovating a bathroom usually means a new water heater position, new pipe routing, and sometimes a switch from storage to tankless. We handle the full plumbing scope: supply lines, drainage, heater install and testing, all coordinated with your contractor's timeline.

View Bathroom Renovation Plumbing

Book Water Heater Repair & Installation in Kuala Lumpur & Selangor Today

Cold water, a leaking tank, or a unit that keeps tripping the breaker: call us and we will get it sorted. Same-day service, upfront pricing, and a 90-day workmanship warranty on every repair. Call +60178717384 now.

Call +60178717384 Call Now

Get in Touch With Us

Call us any time, day or night, and describe the problem. We answer live, give you a price range on the spot, and lock in an arrival window. For non-emergency jobs, same-day slots are usually available if you call before noon. You can also email us with photos of the issue and we will respond within a few hours.

Or call us right now at +60178717384 — we answer.

Valley & City Plumbing KL


  • Phone

    +60178717384
  • Address

    10, Jalan SR 7/10, Taman Serdang Raya, 43300 Seri Kembangan, Selangor, Malaysia

  • Hours

    Mon–Sun: Open 24 Hours
    24/7 Emergency Available

Call +60178717384 Get Quote
Call Quote