Full Diagnosis and Quote
We inspect the bowl, cistern, flange, and supply line, then test the flush and fill cycle. You get a written price before work begins, covering labour and any parts we recommend replacing.
Every job includes the diagnosis, the labour, and a flush test before we leave. Parts are quoted separately if replacement is needed, and we tell you the cost before we start. Here is what is covered in a standard visit.
We inspect the bowl, cistern, flange, and supply line, then test the flush and fill cycle. You get a written price before work begins, covering labour and any parts we recommend replacing.
We replace worn fill valves, flush valves, and flappers with Rubine or Panasonic parts. A running toilet usually traces back to one of these, and swapping them stops the constant water waste.
A leaking base means the wax seal has failed or the flange is cracked. We pull the bowl, replace the seal, repair or swap the flange, and reseat the toilet so it sits firm with no rocking.
If the bowl is cracked or you want a new model, we supply and install it, including new bolts, seals, and supply line. We measure the rough-in first so the new unit fits without tile hacking.
We run at least five full flush cycles, check for drips, and confirm the fill valve shuts off at the right level. Then we remove old parts, wipe the floor, and hand you the 6-month warranty note.
Toilet Repair & Installation in Kuala Lumpur & Selangor is a licensed plumbing service that diagnoses, repairs, or replaces residential and commercial toilets, including cisterns, flush valves, fill valves, wax seals, and floor mountings. A standard repair job takes one to two hours; a full bowl swap with new fittings runs two to three hours. We carry Rubine and Panasonic replacement parts on the van, so most call-outs finish in a single visit without a second trip for spares.
Most calls we get in Selangor come from three situations: a running toilet that will not stop filling, a bowl that rocks on a loose flange, or a choke that a plunger cannot clear. Older terrace houses in Klang and Ampang often have original PVC pipes and worn wax rings, while newer condo units in Puchong and Subang Jaya tend to have concealed cisterns that need a different approach. If you need toilet bowl installation near me in KL and Selangor, we measure the rough-in first so the new unit fits without hacking tiles.
Every job follows the same five steps, whether it is a quick flush tank fix in Petaling Jaya or a full bowl replacement in Klang. You know what happens and when.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Drain Snake
Feeds through the trapway to break up blockages that a plunger cannot shift. We use it on severe chokes before escalating to a hydro-jetter for the main line.
Hydro-jetter
Blasts high-pressure water through the sewer line to clear grease, scale, and roots. We use it when a toilet backs up repeatedly and the block sits deeper in the run.
Leak Detection Kit
Traces hidden leaks at the base, supply line, or cistern bolts. It helps us find the source fast instead of pulling the bowl on a guess.
Pipe Wrench and Pipe Cutter
Used to loosen old fittings, cut out corroded sections of PVC pipes or copper pipes, and fit new joints cleanly without damaging the surrounding line.
Pressure Gauge
Checks supply pressure at the inlet. High pressure wears out fill valves fast, so we measure it and recommend a regulator if the reading is too high.
Soldering Torch
Joins copper pipes where a section needs replacing. We use it when the supply line to the toilet is copper and corroded at the joint.
Rough-In Measurement Before Installation
Before any bowl replacement, we measure the distance from the wall to the floor drain. That number decides which toilet model fits. Getting it right avoids hacking tiles or returning a unit that does not sit properly.
Five-Cycle Flush Test
After every repair or installation, we run at least five full flush cycles and check for drips at the base, supply line, and tank bolts. If anything weeps, we fix it before packing up. You watch the final test.
SPAN-Compliant Fittings and Seals
We fit parts that meet Suruhanjaya Perkhidmatan Air Negara standards, including approved wax seals, supply lines, and valves. That keeps the installation compliant and reduces the chance of early failure.
Waterproofing at the Base
After reseating a toilet, we apply silicone sealant and a waterproofing membrane around the base. It stops water from seeping into the floor if a seal ever fails again, protecting the subfloor and tiles.
01
What we do: We replace the fill valve and flapper, adjust the water level, and run five flush cycles to confirm the cistern stops filling correctly. The whole visit takes about an hour, and we check the other toilets in the house while we are there.
→ The running stops the same day, and your next water bill drops back to normal. You also get a tip on checking the valve every six months to catch wear early.
02
What we do: We disconnect the old unit, cap the supply, and prep the flange. Then we set the new bowl, connect the supply line, seal the base, and test the flush. We coordinate with your tiler so the plumbing rough-in is done before the floor goes down.
→ A new toilet installed level and leak-free, ready for daily use. The bathroom is back in service the same day, and the installation carries a 6-month workmanship warranty.
03
What we do: We treat it as an emergency, dispatch the nearest technician, and isolate the supply on arrival. Then we clear the blockage, check the cistern, and confirm the flush works before leaving. We also check the floor trap for a deeper block.
→ The overflow stops, the floor is dried and cleaned, and the tenant has a working toilet the same night. You avoid water damage to the unit below and a bigger repair bill.
04
What we do: We drain the cistern, replace the tank bolts and washers, and reseal the joint with plumber's putty and silicone sealant. We refill and flush-test to confirm no drips remain, and check the supply line for corrosion while we are in there.
→ No more drips on the floor, and the cistern holds water properly. The fix takes about 45 minutes and prevents floor damage from constant moisture.
Selangor's mix of old and new housing shapes how we work. In older terrace houses around Klang, Ampang, and Serdang, the original PVC pipes and wax seals are often decades old, so we check the flange and the downstream line before assuming a simple valve swap will fix it. In newer condos across Petaling Jaya, Puchong, and Subang Jaya, concealed cisterns and wall-hung bowls need a different approach, and we carry the parts for both. The tropical climate adds its own factor: constant humidity corrodes tank bolts and supply lines faster than in drier countries, so we inspect those on every visit. If you need Selangor toilet leak repair after a heavy monsoon spell, we prioritise those calls because water damage spreads fast. Our vans carry Rubine, Joven, and Panasonic parts, plus PVC pipes, copper pipes, and PEX pipes, so most jobs finish on the first visit. For affordable toilet repair in Kuala Lumpur, we quote before we start and stick to the figure.
Petaling Jaya
A mix of older single-storey homes and newer high-rises. We often see original floor-mounted bowls in the older sections and concealed cisterns in the newer condos, so we carry parts for both.
Klang
Many terrace houses here still run original PVC pipes and worn wax seals. We check the flange and the main line before recommending a repair, since a deeper block is common.
Puchong Prima
High-density condo area with wall-hung and concealed-cistern toilets. Access panels and shut-off valves vary by block, so we confirm the setup when you book.
Ampang
Older walk-up flats and landed homes with a mix of plumbing ages. Water pressure can run low on upper floors, which affects how fast a cistern refills after a flush.
Batu Caves
Landed homes and shoplots with varied plumbing setups. Hard water in some areas leaves scale in the cistern, so we descale the valve seat during repairs.
High humidity year-round
Tank bolts, supply lines, and metal fittings corrode faster than in drier climates. We inspect these on every visit and replace any part showing rust before it fails and floods the floor.
Monsoon-season heavy rain
Heavy rain can back up drains and worsen existing blockages, causing toilet overflows. We prioritise these calls and check the floor trap and main line, not just the bowl.
Hard water in some Selangor areas
Scale builds up in the cistern and on the fill valve, causing slow filling and weak flushes. We descale the valve seat and flush the cistern during repairs to restore proper flow.
Mix of old and new building stock
Older homes may have non-standard rough-in measurements, while newer condos use concealed systems. We measure before any replacement and carry parts for both setups on the van.
Most toilet faults fall into a handful of categories, and each one has a clear fix. Here are the problems we handle most often, and what happens if you leave them alone.
Problem
A running toilet can waste hundreds of litres a day, pushing your water bill up month after month. It also wears out the fill valve faster, turning a small fix into a bigger repair.
Our Fix
We replace the fill valve or flapper with a genuine Rubine or Panasonic part, then adjust the water level so the cistern stops filling at the correct mark. The job takes about an hour and stops the waste immediately.
Problem
A leaking base means the wax seal has failed. Water seeps into the floor, softens the subfloor, and can rot the timber or loosen the tiles around the toilet over time.
Our Fix
We pull the bowl, remove the old seal, inspect the flange, and fit a new wax ring. If the flange is cracked, we repair or replace it before reseating. We reseal the base with silicone sealant and test for leaks.
Problem
Recurring chokes usually mean a blockage deeper in the line, not just at the bowl. Left alone, the backup can flood the bathroom and damage flooring, cabinets, and nearby rooms.
Our Fix
We use a drain snake or hydro-jetter to clear the trapway and the downstream line. If the block sits in the main sewer, we jet the run and camera-check it so you know what caused it and how to prevent a repeat.
Problem
A loose bowl stresses the flange and the wax seal every time it moves. Eventually the seal fails, water leaks at the base, and the flange itself can crack, turning a simple fix into floor work.
Our Fix
We lift the bowl, check the flange and floor surface, replace any damaged bolts or spacers, and reseat the toilet with a fresh seal. New bolts and a shim set keep it firm so it does not move again.
A toilet that fails is not a small problem. It floods floors, wastes water, and disrupts the whole household. Here is what you get when you book us.
Same-Day Response
We schedule most toilet repair jobs in Selangor within the same day you call, and emergency calls get priority. Our technicians carry a leak detection kit and spare flush valves on board, so roughly 8 out of 10 jobs finish on the first visit without waiting for parts.
Upfront Pricing
You get the price before we start, not after. A standard cistern repair sits in the RM120 to RM280 range, and a full toilet replacement runs RM450 to RM1,200 depending on the model. No hidden charges, no surprise add-ons when the invoice arrives.
Genuine Parts Only
We fit Rubine, Joven, and Panasonic flush mechanisms, plus PVC pipes, copper pipes, and PEX pipes where the line calls for them. Cheap imitation valves fail within months. Our replacements carry a 6-month workmanship warranty on parts and labour.
Clean, Tidy Work
We lay floor protection, cut tiles only when necessary, and reseal with silicone sealant and waterproofing membrane before we leave. You get a dry bathroom floor and a toilet that flushes properly, not a mess to clean up after the technician drives off.
Google ★★★★★4.9
Called them for a leaking toilet base in our Subang Jaya home. They arrived on time, diagnosed a failed wax seal, and replaced it with a new flange. Took about 90 minutes. Floor has been dry since. Fair price and they cleaned up properly.
Google ★★★★★4.8
Our office toilet in Petaling Jaya choked badly and a plunger did nothing. They came same day, used a drain snake, and cleared a block in the main line. Explained what caused it and how to avoid a repeat. Professional and quick.
Google ★★★★★4.9
Replaced two old toilets in our Klang rental units. They measured the rough-in first, supplied new bowls, and installed both in one visit. No leaks, no wobble, and the tenants are happy. Will use them for other plumbing work.
Google ★★★★★4.8
Emergency call at night when our toilet overflowed in Puchong. They answered, dispatched a technician, and had it cleared within the hour. Charged the emergency rate they quoted upfront. Grateful for the fast response.
Our team has handled toilet repair and installation across Selangor and Kuala Lumpur for years, from single-bowl fixes in walk-up flats to full replacements in new condo launches. We hold a Suruhanjaya Perkhidmatan Air Negara (SPAN) license and CIDB registration, and our technicians are trained to Certified Plumber (Malaysia) standards. We work with the tools of the trade daily: pipe wrench, plunger, drain snake, hydro-jetter, pipe cutter, soldering torch, pressure gauge, and leak detection kit. That means we diagnose fast and fix it right the first time.
Our toilet service in Selangor reaches every corner of the state, from the Klang corridor to the Puchong and Subang belt, plus Kuala Lumpur and the surrounding townships. Each area has its own plumbing quirks, and our technicians know them. Here are some of the cities we cover regularly.
We handle toilet repair and installation in Ampang's mix of walk-up flats and landed homes, including low-pressure cistern issues on upper floors and worn wax seals in older units.
Old Klang Road's older commercial and residential buildings often have original PVC pipes and tired fittings. We repair leaking bases, replace valves, and clear chokes in these established properties.
Setiawangsa's hillside homes and condos get fast same-day toilet service from us, covering running cisterns, loose bowls, and full replacements with genuine Rubine and Panasonic parts.
Petaling Jaya is one of our busiest areas. We work on older terrace houses with floor-mounted bowls and newer condos with concealed cisterns, so we carry parts for both setups.
SS20's family homes often need cistern repairs and wax seal replacements. We arrive with the right parts, quote upfront, and finish most jobs in a single visit without a second trip.
Subang Perdana's residential blocks get prompt toilet repair and installation from our team, including concealed-cistern fixes and full bowl swaps with proper resealing and flush testing.
Teluk Pulai's Klang-area homes deal with hard water scale in cisterns. We descale valves, replace worn parts, and restore proper flush performance during the same visit.
Puchong Prima's high-density condos need careful work around concealed cisterns and access panels. We confirm the setup when you book and bring the right parts for the block.
Batu Caves' landed homes and shoplots have varied plumbing ages. We repair leaking bases, replace flanges, and clear blockages, checking the main line when a choke keeps returning.
Serdang's growing residential areas get same-day toilet service from us, covering everything from a running fill valve to a full bowl replacement with new seals and fittings.
Telok Panglima Garang's newer developments and older kampung homes both get our toilet repair and installation service, with parts on the van for same-day fixes.
Real experiences from customers who chose our Toilet Repair & Installation services.
“Our upstairs toilet had been running non-stop for weeks and the water bill showed it. The technician arrived in the afternoon, replaced the fill valve with a Panasonic unit, and tested it five times before leaving. Bill dropped back to normal the next month. Clean work, no mess left behind.”
Farah M.
Homeowner, Petaling Jaya
“I manage three rental units in Klang and one had a badly choked toilet that a plunger could not touch. They came out same day, used a drain snake, and found the block was in the main line. Cleared it, flushed everything, and charged what they quoted. I now call them for all three units.”
Ramesh K.
Landlord, Klang
“My condo toilet was leaking at the base and the floor was always damp. They diagnosed a failed wax seal, replaced it, and resealed with waterproofing membrane. Took about 90 minutes. No leak since, and they explained how to check the cistern every few months to catch problems early.”
Michelle T.
Condo Owner, Puchong Prima
Real answers to the questions we hear most often from local homeowners and property managers.
When a toilet overflows at 2 a.m. or a supply line bursts, our emergency team responds fast across Selangor and KL. We isolate the water, stop the damage, and fix the fault on the spot, so you are not mopping floors until morning.
View Emergency Plumbing ServiceWe install and repair Joven and Alpha water heaters, often in the same visit as a toilet fix. If your heater leaks or trips the breaker, we test the unit, replace faulty parts, and confirm safe operation before we leave.
View Water Heater Repair & InstallationA choked toilet often points to a blocked drain downstream. We clear floor traps, sink lines, and main drains with a drain snake or hydro-jetter, then flush-test the whole run so the problem does not come back next week.
View Clogged Drain ClearingLeaking PVC pipes or corroded copper pipes near the toilet base cause damp floors and rising water bills. We trace the leak with a detection kit, cut out the damaged section, and rejoin with new fittings and Teflon tape.
View Pipe Leak RepairLow water pressure makes a toilet slow to fill and weak on the flush. We install Grundfos and Wilo pumps sized to your home, then balance the pressure so every tap and cistern in the house works properly.
View Water Pump InstallationIf you are retiling or moving fixtures, we handle the plumbing rough-in: relocating the soil pipe, setting new floor flanges, and waterproofing the wet area before the tiles go down. We coordinate with your contractor to keep the schedule on track.
View Bathroom Renovation PlumbingCall us any time, day or night, and describe the problem. We answer live, give you a price range on the spot, and lock in an arrival window. For non-emergency jobs, same-day slots are usually available if you call before noon. You can also email us with photos of the issue and we will respond within a few hours.
Phone
+60178717384Address
10, Jalan SR 7/10, Taman Serdang Raya, 43300 Seri Kembangan, Selangor, Malaysia
Hours
Mon–Sun: Open 24 Hours
24/7 Emergency Available