Valley & City Plumbing KL
Get Estimate

Sink & Faucet Repair in Kuala Lumpur & Selangor

Same-day tap, basin and sink fixes across Selangor


Sink & Faucet Repair in Kuala Lumpur & Selangor stops the drip, the puddle under the cabinet and the tap that sprays sideways. We handle leaking mixer taps, corroded angle valves, cracked basins and slow-draining kitchen sinks for homes and shops across the state. If your tap has been dripping since last month, that is wasted water on your bill every single day.

Clean and bright public bathroom with sinks, mirrors, and a hand dryer.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed

What Our Sink & Faucet Repair Includes

Every visit covers diagnosis, the repair itself, and a pressure test before we leave. Parts are quoted separately so you know exactly what you are paying for. If we find a bigger issue, we tell you the cost before touching anything.

Full Tap Diagnosis

We shut off the angle valve, inspect the cartridge, washer, O-ring and packing nut, and check the waste trap and pipe joint. You get a clear explanation of what failed and a fixed price for the repair before we start work.

Cartridge and Washer Replacement

Worn cartridges and washers are the most common cause of a leaking faucet. We carry common Malaysian sizes on the van and swap them on the spot. Most replacements take 30 to 45 minutes and stop the drip immediately.

Waste Trap and Drain Clearing

If the sink drains slowly, we clear the P-trap with a drain snake and flush the line. This is often bundled with a tap repair since both problems share the same cabinet space. We check flow before we finish.

Resealing and Joint Repair

We reseal the tap base with silicone sealant, refresh the Teflon tape on threaded joints, and check the flexi hose connection. This stops water from seeping under the counter and damaging the cabinet board.

Pressure Test and Cleanup

Before leaving, we run the tap hot and cold, watch every joint for drips, and confirm the cabinet floor stays dry. We wipe down the work area and bag the old parts so you can see what was replaced.

What Sink & Faucet Repair in Kuala Lumpur & Selangor Covers


Sink & Faucet Repair in Kuala Lumpur & Selangor is the trade work that restores a working tap, basin or sink to full function: reseating or replacing the cartridge, swapping a worn washer, re-cutting the thread on a corroded angle valve, sealing the waste trap, and testing the whole assembly under pressure before we pack up. Most jobs take 45 to 90 minutes. We carry Rubine and Alpha cartridges, Panasonic shower mixers and common ceramic disc inserts on the van, so a single visit usually finishes the job.

In Selangor's high-rise apartments and older terrace houses, the same three problems show up again and again: a leaking faucet that stains the countertop, a kitchen sink that backs up because grease has hardened in the P-trap, and low water pressure at the basin because the aerator is choked with sediment. We see this in Kepong walk-ups and Kajang double-storey homes alike. If you have been searching for sink and faucet repair near me in KL and Selangor, our team covers the whole state with a stocked van and a pipe wrench ready.

How Our Sink and Faucet Repair Visit Runs

You call, we confirm a slot, and a technician arrives with the tools and parts to finish most jobs in one trip. Here is the sequence from your first message to the final pressure test.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

Pipe Wrench

Used to hold and turn angle valves, tap bodies and pipe fittings without crushing the chrome. Essential for replacing seized valves and tightening joints to the correct torque.

Drain Snake

Clears blockages in the P-trap and branch waste line when a sink drains slowly. We feed it through the trap and pull out grease, hair and debris without removing the whole assembly.

Pressure Gauge

Measures supply pressure at the tap to confirm whether low flow is a clogged aerator, a failing pump, or a genuine pressure problem. Takes the guesswork out of diagnosis.

Leak Detection Kit

Traces water pooling under the sink to its actual source, which is often a waste joint or flexi hose rather than the tap. Stops us from replacing parts that are still good.

Pipe Cutter

Cuts copper and PVC pipe cleanly when a section needs replacing. A clean cut means a proper joint that will not leak under pressure.

Silicone Sealant and Plumber's Putty

Seals the tap base and waste flange to the sink so water cannot seep under the counter. We use the correct product for the surface, since putty and silicone behave differently on stone and stainless steel.

Methods & Standards

Isolate, Diagnose, Quote

We shut off the angle valve first, then diagnose the actual failure before quoting. This means you get a fixed price based on what is really wrong, not a guess. It also protects your floor from further water while we work.

Cartridge and Washer Replacement

For a leaking faucet, we replace the ceramic cartridge or rubber washer rather than the whole tap where possible. This is cheaper for you and keeps the original fixture. We match the cartridge to the tap brand, including Rubine and Alpha models.

Pressure Testing Before Sign-Off

Every repair is tested with the tap running hot and cold while we watch the joints. We do not leave until the cabinet floor stays dry. This is how we catch a slow seep that would otherwise show up as a leak next week.

SPAN-Compliant Fittings

All replacement parts and fittings meet SPAN requirements for water fittings in Malaysia. That matters for warranty and for insurance if a leak ever causes damage. We do not fit uncertified parts to save a few ringgit.

When to Call Us for Sink & Faucet Repair

01

You are moving into a resale condo in USJ 1-USJ 27 and the previous owner's taps are stiff and dripping.

What we do: We inspect every tap, angle valve and waste joint in the kitchen and bathrooms, replace worn cartridges, and reseal the bases. One visit covers the whole unit, so you start fresh without inheriting old leaks.

→ All taps work smoothly, no drips, and you know the shut-off valves actually turn. Most units are done in half a day.

02

A restaurant or cafe kitchen sink in Bandar Puteri Klang blocks every few weeks from grease buildup.

What we do: We clear the line with a hydro-jetter, inspect the P-trap and branch pipe, and recommend a grease trap service schedule. We also check the tap and pre-rinse sprayer for worn seals.

→ The sink drains fast again, and a maintenance schedule keeps it that way instead of emergency call-outs during service hours.

03

The bathroom basin tap in your Kajang terrace house has been dripping for months and the cabinet is starting to smell musty.

What we do: We replace the cartridge, reseal the base, check the waste trap for leaks, and treat the damp cabinet area. If the board is already swollen, we tell you what needs replacing.

→ The drip stops, the musty smell clears once the area dries, and the cabinet stops getting wetter every day.

04

You run an office in Putrajaya and the pantry tap has low pressure, making it slow for staff to fill water bottles.

What we do: We flush the aerator, check the angle valve and supply line, and test flow. If the issue is upstream pressure, we test with a pressure gauge and advise on a booster pump.

→ Full pressure returns at the pantry tap, and staff stop queuing. The fix usually takes under an hour.

How Sink & Faucet Repair Runs Across Selangor

Selangor's mix of old and new housing shapes every job. In older terrace houses around Kajang and Klang, we often find original gate valves that have not been turned in years, so we replace them before touching the tap. In newer high-rise condos in Tropicana and USJ 1-USJ 27, the challenge is access and isolation: the angle valve is often tucked behind a cabinet panel, and the building's riser needs coordinating with management. Water quality also matters. Sediment from ageing rooftop tanks clogs aerators and scores cartridges, which is why taps in the same unit tend to fail one after another. We flush the aerator and check the tank during the visit. For a kitchen sink repair service in Selangor for blocked pipe issues, we clear the trap and branch line, then confirm flow with hot water. If you need affordable sink repair in Kuala Lumpur for a rental unit, we can batch multiple taps into one visit to keep the cost down. We route vans by zone so travel time stays short and your slot is honoured.

Neighborhoods We Serve

  • Kepong

    Older walk-up apartments and terrace houses with original gate valves. We replace seized angle valves before tap work so isolation is possible in an emergency.

  • Kota Kemuning

    Newer linked homes with modern mixer taps. Common issue is hard water scaling on cartridges, which we descale or replace depending on wear.

  • Bandar Puchong Jaya

    High-density condo blocks where the angle valve is often behind a cabinet panel. We plan access before arrival to avoid cutting into the cabinet.

  • Putrajaya

    Government and office buildings with pantry sinks under heavy daily use. We schedule repairs outside peak hours to avoid disrupting staff.

  • Meranti Jaya

    Mixed residential and light industrial area. We handle both home basins and commercial sink taps, often with sediment issues from shared supply lines.

Local Conditions We Plan For

  • High sediment from ageing rooftop water tanks

    Clogs aerators and scores ceramic cartridges, causing low flow and drips. We flush the aerator and check the tank so the new parts are not fighting dirty water.

  • Hard water scaling in newer developments

    Leaves white deposits on cartridges and tap spouts, making handles stiff and flow uneven. We descale or replace the cartridge depending on how far the scale has gone.

  • High-rise isolation and access limits

    Angle valves tucked behind cabinets or in service risers slow the job. We confirm access and building rules before arrival so the visit runs without delays.

  • Mixed old and new pipe materials

    Copper, PVC and PEX pipes in the same unit behave differently under pressure. We match fittings correctly and test joints so a repair on one material does not stress another.

Kitchen Tap Drip in Taman Desa

Before

A kitchen mixer tap had been dripping for two months. The cabinet board under the sink was swollen and the chrome was stained. The homeowner had tried tightening the handle, which made it worse.

After

We replaced the worn ceramic cartridge, resealed the base, and cleared the slow-draining P-trap. The drip stopped completely, flow returned to normal, and the cabinet was left to dry out. Total time on site was 70 minutes.

Maintenance: Do not overtighten the handle when closing the tap. Flush the aerator every six months and check under the sink for dampness after heavy use.

Before

A bathroom basin tap was spraying sideways and the angle valve was seized, so the supply could not be shut off. Water was pooling on the counter and dripping into the cabinet below.

After

We replaced the seized angle valve, fitted a new mixer tap, and pressure-tested the assembly. The counter stayed dry, the cabinet stopped getting wet, and the shut-off valve now turns freely. Job took about two hours.

Maintenance: Turn the angle valve closed and open once a year to keep it from seizing. Wipe the tap dry after use to slow chrome wear.

Before

A cafe kitchen sink was backing up every few weeks from grease buildup. The pre-rinse sprayer was also leaking at the joint, adding water to the floor during service hours.

After

We cleared the branch line with a hydro-jetter, replaced the sprayer joint seal, and checked the tap cartridge. The sink drained fast and the floor stayed dry through the next service. We recommended a monthly grease trap schedule.

Maintenance: Flush the sink with hot water after each service and keep the grease trap on a monthly cleaning schedule to prevent repeat blockages.

Sink and Faucet Problems We Fix Every Week

Most calls come down to five recurring issues. Here is what they look like, what happens if you leave them, and how we fix them properly.

Problem

Tap drips constantly even when fully closed

Wastes thousands of litres a year, stains the basin, and corrodes the chrome finish. The drip also keeps the cabinet damp, which swells the board over time.

Our Fix

We replace the worn cartridge or washer, reseat the valve, and test the tap under full pressure. Most drip repairs finish in under an hour and stop the water loss immediately. We carry common cartridges so no second visit is needed.

Problem

Water pools under the sink after every use

The cabinet board warps, mould grows, and the leak can spread to the floor below in a condo. Left long enough, it becomes a structural repair, not a plumbing one.

Our Fix

We trace the source with a leak detection kit, which is often the waste trap joint or a loose flexi hose rather than the tap itself. We reseal the joint, replace the hose if needed, and confirm the underside stays dry.

Problem

Kitchen sink drains slowly or backs up

Standing water breeds bacteria, smells, and eventually blocks completely. A fully blocked sink means you cannot use the kitchen until it is cleared.

Our Fix

We clear the P-trap and branch line with a drain snake or hydro-jetter, then flush with hot water to move residual grease. We check the tap and waste assembly while we are there so the whole sink works properly.

Problem

Low water pressure at the basin tap

Makes washing hands and dishes slow and frustrating. Often the aerator is clogged with sediment from the water tank, which means other taps will follow.

Our Fix

We remove and flush the aerator, check the angle valve is fully open, and test flow at the spout. If sediment is coming from the tank, we flag it and can inspect the tank during the same visit.

Problem

Angle valve seized or will not shut off

You cannot isolate the tap for repairs, and a sudden leak becomes a flood because there is no way to stop the supply quickly.

Our Fix

We replace the seized angle valve with a new one, which restores your ability to shut off the tap in an emergency. This is a 30 to 45 minute job and worth doing before any tap repair that needs isolation.

Why Fix a Leaking Tap Before It Spreads

Why Fix a Leaking Tap Before It Spreads

A dripping tap wastes more than water. It corrodes the counter, warps the cabinet board, and turns a RM120 cartridge swap into a RM900 cabinet rebuild. Here is what you actually get when we fix it early.

  • Stop the Water Bill Bleed

    A tap dripping once per second wastes roughly 11,000 litres a year. At Selangor domestic rates that is real money leaving your account every month. We reseat or replace the cartridge and the drip stops the same visit, usually within the hour.

  • Protect Cabinets and Counters

    Water that escapes a leaking faucet runs down the back of the cabinet and swells the particle board within weeks. We seal the base, replace the Teflon tape and plumber's putty, and check the waste pipe joint so the underside stays dry after we leave.

  • Restore Full Water Pressure

    Low flow at the basin is usually a clogged aerator or a half-closed angle valve, not a supply problem. We flush the aerator, open the valve fully, and test flow at the spout. Most basins come back to full pressure in under 30 minutes.

  • One Visit, Stocked Van

    We carry Grundfos pressure gauges, pipe cutters, silicone sealant and common tap cartridges on board. That means fewer return trips and a fixed price quoted before we start. If a part is unusual, we tell you the exact cost before ordering it.

Licensed, Insured and Warrantied

Licensed & Certified

  • SPAN Licence — issued by Suruhanjaya Perkhidmatan Air Negara
  • Certified Plumber (Malaysia) — issued by Certified Plumber (Malaysia)
  • MS ISO 9001 — issued by Department of Standards Malaysia
  • CIDB Registration — issued by Construction Industry Development Board Malaysia

Verified Reviews

Google ★★★★★4.9

Fixed a leaking kitchen tap and a slow drain in one visit. The technician explained what was wrong, quoted a fixed price, and finished in about an hour. No mess left behind. Would call again for any plumbing issue.

Google ★★★★★4.8

Called in the morning about a basin tap spraying water. They came the same afternoon, replaced the angle valve and the tap, and tested everything. Fair price and clean work. Recommended for anyone in Selangor.

Google ★★★★★4.9

We use them for our rental units. They batch multiple tap repairs into one trip and invoice clearly. Tenants have not complained since. Reliable and easy to schedule.

Google ★★★★★4.8

The tap in our cafe kitchen was leaking at the joint during service. They came after hours, fixed it, and cleared the drain too. Kept the disruption to a minimum. Good trade work.

Local Experience You Can Actually Check

Our technicians are trained on residential and commercial tap systems, from old gate valves in 1980s terrace houses to modern ceramic cartridge mixers in new condos. We work to SPAN licence requirements and MS ISO 9001 quality standards, and our team holds Certified Plumber (Malaysia) credentials. We have handled everything from a single dripping kitchen tap in Taman Desa to full basin replacements across a Putrajaya office block. Every job is pressure-tested before we sign off.

  • Certified Plumber (Malaysia) technicians trained on ceramic cartridge and washer tap systems
  • SPAN licence compliance for all water fittings and installation work
  • Stocked with Rubine, Alpha and Panasonic cartridges for common Malaysian tap models
  • Experienced with high-rise condo plumbing, terrace houses and shophouse basins
  • Every repair pressure-tested and warrantied before we leave the site
Get Started Today
Local Experience You Can Actually Check

Cities We Serve for Sink & Faucet Repair in Selangor

We cover the whole state with routed vans and stocked parts, so most sink repair service Kuala Lumpur and Selangor jobs finish in one visit. From the Klang corridor to the Hulu Langat side and up through Gombak, our technicians know the building types and common tap failures in each area. Below are some of the neighbourhoods we work in most often.

Kepong

Older walk-up apartments and terrace houses with original gate valves. We replace seized angle valves before tap work so isolation is possible in an emergency.

Taman Desa

Linked homes and low-rise condos with a mix of old and new taps. Common calls are dripping kitchen mixers and slow-draining sinks from grease buildup in the P-trap.

Kota Kemuning

Newer linked homes with modern mixer taps. Hard water scaling on cartridges is the usual issue, which we descale or replace depending on wear.

Tropicana

High-rise condos where the angle valve is often behind a cabinet panel. We plan access before arrival and coordinate with management for riser isolation.

USJ 1-USJ 27

Dense residential neighbourhoods with a wide mix of tap brands. We carry common cartridges for Rubine, Alpha and Panasonic models so most repairs finish in one visit.

Bandar Puteri Klang

Shophouses and homes with heavy kitchen use. Grease blockages and leaking pre-rinse sprayers are common, and we clear the line and reseal joints in one trip.

Bandar Puchong Jaya

Condo blocks and terrace houses with sediment issues from shared supply lines. We flush aerators and check the tank so new cartridges are not fighting dirty water.

Meranti Jaya

Mixed residential and light industrial area. We handle both home basins and commercial sink taps, often with sediment problems from shared supply lines.

Kajang

Older terrace houses and newer developments side by side. We replace worn gate valves and cartridges, and clear slow drains from years of grease and debris.

Putrajaya

Government and office buildings with pantry sinks under heavy daily use. We schedule repairs outside peak hours and test flow so staff are not disrupted.

What Our Customers Say

Real experiences from customers who chose our Sink & Faucet Repair services.

“The kitchen tap had been dripping for two months and the cabinet board was already swelling. The technician arrived in the afternoon, showed me the worn cartridge, and replaced it in about 40 minutes. He also cleared the slow drain while he was there. Fixed price, no surprises, and the counter stayed dry.”

F

Farah A.

Homeowner, Taman Desa

“I manage three rental units and the basins keep leaking. Called on a Monday, they came Tuesday morning and fixed two taps and a shower mixer in one trip. They had the cartridges on the van, so no waiting for parts. Invoice was clear and the tenants were happy. Will use again.”

R

Ramesh K.

Landlord, Bandar Puchong Jaya

“My basin tap was spraying sideways and the angle valve was seized. I was worried it would flood the bathroom. They shut off the supply, replaced the valve and the tap, and pressure-tested everything before leaving. Took about two hours. Clean work and they cleaned up after themselves.”

M

Mei Ling T.

Condo Owner, Tropicana

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How much does sink and faucet repair cost in Kuala Lumpur and Selangor?
Most 2026 jobs run RM120 to RM450 depending on the part and access. A cartridge or washer replacement is typically RM120 to RM280. A full faucet replacement runs RM180 to RM450 including the new unit. Clearing a blocked P-trap adds RM80 to RM150. We quote a fixed price after diagnosis, before any work starts.
Who fixes leaking faucets in KL and Selangor?
We do. Valley & City Plumbing KL sends a Certified Plumber (Malaysia) technician to your home or shop, diagnoses the leak, and repairs or replaces the tap on the spot. We cover the whole state, from Kepong and Tropicana to Kajang and Putrajaya. Call us and we will confirm a slot, usually same day.
How to stop a dripping tap in Malaysia?
Shut the angle valve under the sink first, then the drip usually means a worn washer or a scored ceramic cartridge. You can try tightening the packing nut a quarter turn, but if the drip continues the cartridge needs replacing. We carry common Malaysian cartridges on the van and swap them in under an hour.
Do you offer same day faucet repair in Kuala Lumpur?
Yes. We keep same-day slots for urgent calls, including burst flexi hoses and taps that will not shut off. Call before noon and we aim to reach you the same day across most KL and Selangor areas. Emergency calls after hours get priority dispatch, and we confirm the arrival window when you book.

Related Services

Emergency Plumbing Service

When a sink or tap fails at 2 a.m. and water is spreading, our emergency team shuts off the supply, contains the leak, and makes the repair safe. We carry the same stocked van, so most emergency sink and faucet calls are resolved in one visit.

View Emergency Plumbing Service

Water Heater Repair & Installation

A leaking faucet and a failing water heater often share the same root cause: pressure problems in the line. We check both while on site. If your Joven or Alpha heater is tripping or leaking, we can repair or replace it during the same visit.

View Water Heater Repair & Installation

Clogged Drain Clearing

A kitchen sink that drains slowly usually has grease buildup in the P-trap or the branch line. We clear it with a drain snake or hydro-jetter, then check the tap and waste joint so the whole sink assembly works properly again.

View Clogged Drain Clearing

Pipe Leak Repair

Water pooling under the sink is not always the tap. A pinhole leak in a copper or PVC pipe can look identical. We trace the source with a leak detection kit, repair the pipe, and confirm the tap assembly is sound before we leave.

View Pipe Leak Repair

Toilet Repair & Installation

A running toilet and a dripping tap both waste water and both point to worn seals. If you are already booking us for sink and faucet work, we can service the toilet cistern and inlet valve in the same visit and save you a second call-out fee.

View Toilet Repair & Installation

Water Pump Installation

Low pressure at every tap often means the booster pump is failing, not the faucet. We test the pump with a pressure gauge, and if it needs replacing we install a Grundfos or Wilo unit sized to your home so all your taps flow properly.

View Water Pump Installation

Book Sink & Faucet Repair in Kuala Lumpur & Selangor Today

A dripping tap gets worse, not better. Call us and we will confirm a same-day or next-day slot, quote a fixed price after diagnosis, and finish most repairs in one visit. Every job is warrantied.

Call Now Book a Repair

Get in Touch With Us

Call us any time, day or night, and describe the problem. We answer live, give you a price range on the spot, and lock in an arrival window. For non-emergency jobs, same-day slots are usually available if you call before noon. You can also email us with photos of the issue and we will respond within a few hours.

Or call us right now at +60178717384 — we answer.

Valley & City Plumbing KL


  • Phone

    +60178717384
  • Address

    10, Jalan SR 7/10, Taman Serdang Raya, 43300 Seri Kembangan, Selangor, Malaysia

  • Hours

    Mon–Sun: Open 24 Hours
    24/7 Emergency Available

Call +60178717384 Get Quote
Call Quote